87
IGP-RAPID®complete 8763A-A1
Matt powder coating on a polyester resin base, weather-resistant and highly reactive.
download PDF
Proprietà
- opaco
- Natural smooth
- Tinte unite
- Industrial outdoor quality
Proprietà delle polveri
Granulometria:
< 100 μm
Corpi solidi:
> 99 %
Densità:
1.3 kg/l-1.6 kg/l
Stoccaggio:
min. 6 months a ≤ 15 °C
min. 12 months a ≤ 5 °C
min. 24 months a ≤ -20 °C
in an unopened original container
Color tones:
RAL and NCS-S shades, individual colors on request
Caratteristiche del film
Testato per
Substrati:
Coil-coated galvanized steel
Spessore:
80 μm - 120 μm
Temperatura dell’oggetto:
130 °C, 3 min.
Struttura superficiale
Brillantezza:
20-30 R’/60°
DIN EN ISO 2813 2015-02
Prove meccaniche
Cross-cut adhesion test
≤ 1
DIN EN ISO 2409 2020-12
Test di resistenza agli agenti atmosferici
1 year Florida, 5° south
> 50 % Brillantezza residua
DIN EN ISO 2810 2021-01
QUV/SE-B-313, 300h
> 50 % Brillantezza residua
DIN EN ISO 16474-3 2014-03
Xenon-arc lamps, 1000h
> 50 % Brillantezza residua
DIN EN ISO 16474-2 2014-03
Verifiche della resistenza a corrosione
Condensation water test, 1000h
Gt ≤ 1
DIN EN ISO 6270-2 2018-04
Natural salt spray test, 1000h
Gt ≤ 1
DIN EN ISO 9227 2017-07
Prove chimiche
Acetone test
2N Level 2
IGP AA341.58
Applicazione
Pretrattamento
Precoated metal should be degreased and sanded to ensure intercoat adhesion.
The suitability of the substrate and pretreatment method used is generally to be tested by the coater in advance with appropriate test methods.
The minimum requirement is to carry out a boiling water test with a subsequent cross-cut adhesion and tape test. We refer to the guidelines of the GSB International, Qualicoat and Qualisteelcoat certifications. For further information: see also our special leaflet on pre-treatment (IGP-TI 100).
Impianti di verniciatura
All conventional electrostatic systems with corona charging.
For the construction and operation of powder coating plants, the following regulations must be complied with: ATEX RL 2014/34/EU, EN 50177, DIN EN 16985.
For the construction and operation of powder coating plants, the following regulations must be complied with: ATEX RL 2014/34/EU, EN 50177, DIN EN 16985.
Spessore del film consigliato
80 μm - 120 μm
A homogeneous coating result with textured coatings or article-and color specific differences in hiding power may require higher coating thicknesses. The corresponding processing guidelines must be observed.
For a pre-calculation of the required powder coating quantity, the necessary coating thickness must be determined for each article.
For a pre-calculation of the required powder coating quantity, the necessary coating thickness must be determined for each article.
Condizioni di cottura
| Toggetto | t min | t max |
|---|---|---|
| 125 °C | 5 minutes | 9 minutes |
| 130 °C | 3 minutes | 7 minutes |
| 140 °C | 2 minutes | 5 minutes |
Per accertare le condizioni di cottura migliori si consiglia, in ogni caso, di effettuare prove pratiche con il rispettivo oggetto e forno di polimerizzazione.
Recupero
Small portions of recycled powder can be added, automatically if possible, to the fresh powder. Important: Keep overspray to an absolute minimum. Processing instruction VR214 must be observed.
Altre informazioni
Imballaggio
20 kg cardboard box with inserted antistatic PE liner
Protezione delle superfici verniciate
Coated parts should be packed after cooling with suitable materials without plasticizers. They should be stored protected from the weather to avoid the formation of condensation and thus water spots on the coating.
Pulizia
The coated parts must be cleaned according to the directives RAL-GZ 632 or SZFF 61.01.
Rimozione e smaltimento della pittura
After use, coated goods should be supplied to the normal recycling process. The disposal methods for sludges or residual powders must be observed in accordance with the local official provisions whilst taking Waste Code “080201 Coating Powder Wastes” in accordance with the European Waste Catalogue into consideration.
Le presenti informazioni di natura tecnica relative all’utilizzo sono fornite sulla base delle conoscenze attuali. Tuttavia devono essere considerate come indicazioni non vincolanti che non esonerano dall’effettuazione di controlli autonomi. Utilizzo, destinazione e applicazione di prodotti hanno luogo senza possibilità di controllo da parte nostra e, pertanto, soggiacciono esclusivamente alla vostra responsabilità.
Prima dell’applicazione consultare la scheda di sicurezza.
Prima dell’applicazione consultare la scheda di sicurezza.
